Bosch Smart System error codes
All 555 Bosch Smart System codes we have documented: what each one means, what stops working and what you can do yourself before going to a dealer. Applies to Performance Line CX/CX-R, SX, Performance Line; Kiox 300/500, Purion 200, Nyon, LED Remote / System Controller.
Six-character codes (for example 523003 or 50001D) appear on Kiox, Nyon, Purion 200 and other smart system displays and can be acknowledged with the remote; the eBike Flow app shows the same code with a description. On bikes without a display, the LED Remote or System Controller flashes and the code is only visible in the app.
Get Bosch news & firmware updates in Telegram| Code | Meaning | What to do |
|---|---|---|
| 500006, 500007, 500008, 50000B, 50000D, 50000E, 50000F, 500010, 500012, 500013, 500014, 500015, 500016, 500017, 500018, 500019, 50001D, 501000, 501001, 501002, 501003, 501004, 501005, 501006, 501007, 501008, 50100D, 501011, 501012, 502000, 502001, 502002, 502003, 502004, 502009, 503013, 503014, 503015, 503016, 503017, 503018, 503019, 505002, 505003, 505004, 505010, 505020, 506002, 506003, 506004, 506101, 506102, 506103, 514014, 514015 | Drive unit: Motor control fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 50000C, 504000, 505120 | Drive unit: Motor control fault. | Dealer job: contact a Bosch eBike dealer. |
| 50001B, 566100 | Drive unit: Drive unit configuration error. | Dealer job: contact a Bosch eBike dealer. |
| 50001C, 50100C, 50100E, 50100F | Drive unit: Motor control fault. | Run an eBike update in the Flow app if one is available, then restart. If it persists, see a Bosch eBike dealer. |
| 501009 | Drive unit: Motor control fault. | Restart and run an eBike update if available. If it persists, check the battery sits tightly in an undamaged holder and the contacts are clean. If it persists, see a Bosch eBike dealer. |
| 50100A, 50100B, 503001, 503004, 540022, 540023 | Drive unit: Drive unit too hot. (error, warning) | Switch off and let the drive unit cool down for a few minutes, then restart. If it persists, see a Bosch eBike dealer. |
| 501010 | Drive unit: Motor control fault. | Restart. On Hub Line drives, check the plug at the drive unit is secure. If it persists, see a Bosch eBike dealer. |
| 502005 | Drive unit: Drive unit too hot. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 502006, 502007 | Drive unit: Drive unit voltage too low. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 502008 | Drive unit: Drive unit voltage too high. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 503000 | Drive unit: Electrical connection to the drive unit interrupted. | Check the cable and plug between control unit and drive unit for damage and a secure fit, then restart. If it persists, see a Bosch eBike dealer. |
| 503002 | Drive unit: Drive unit too cold. | Move the bike somewhere warmer for a few minutes and check the drive unit cable and plug, then restart. If it persists, see a Bosch eBike dealer. |
| 503005, 503007 | Drive unit: Drive unit too cold. | Move the eBike somewhere warmer for a few minutes, then restart. If it persists, see a Bosch eBike dealer. |
| 503006, 51301D, 51301E | Drive unit: Drive unit too hot. | Let the drive unit cool down for a few minutes, then restart. If it persists, see a Bosch eBike dealer. |
| 503008 | Drive unit: Drive unit power output fault. | Check the connected accessory and its cabling. If it persists, see a Bosch eBike dealer. |
| 503009 | Drive unit: Display connection fault. | Check the display, its cabling and anything powered from it. If it persists, see a Bosch eBike dealer. |
| 50300A | Drive unit: Lighting fault. | Check the lights and their cabling. If it persists, see a Bosch eBike dealer. |
| 50300B | Drive unit: The lights draw too much power. | Test with one light or no lights connected, and check the front and rear light cabling. If it persists, see a Bosch eBike dealer. |
| 50300C | Drive unit: Fault at the drive unit's 12 V output. | Check the connected accessory and its cabling. If it persists, see a Bosch eBike dealer. |
| 50300D | Drive unit: Too much power drawn from the 12 V output. (warning) | Restart, then check the connected accessory and its cabling. If it persists, see a Bosch eBike dealer. |
| 50300E | Drive unit: Drive unit power supply fault. | Check the battery is seated correctly. If it persists, see a Bosch eBike dealer. |
| 50300F, 50301C | Drive unit: Too much power drawn from the 12 V output. (error, warning) | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 503011, 503012 | Drive unit: Drive unit power supply fault. | Check the cabling between battery and drive unit. If it persists, see a Bosch eBike dealer. |
| 50301A | Drive unit: Fault in the power supply to external connections. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 50301E | Drive unit: Communication error between drive unit and ABS (front sensor). | Check the ABS speed sensor on the front wheel for damage and loose bolts or cables. If it persists, see a Bosch eBike dealer. |
| 50301F | Drive unit: ABS communication error (rear sensor). | Check the ABS speed sensor on the rear wheel for damage and loose bolts or cables. If it persists, see a Bosch eBike dealer. |
| 503020, 503021 | Drive unit: Thumb throttle fault. | Restart and check the thumb throttle is connected properly. If it persists, see a Bosch eBike dealer. |
| 503022 | Drive unit: Torque measurement fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 503023 | Drive unit: Brake signal fault. | Dealer job: contact a Bosch eBike dealer. |
| 507000, 507001 | Drive unit: Drive unit power supply fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 510001, 510002, 510003, 510004, 510005, 51000A, 51000B, 51000C, 510010, 510011 | Drive unit: Torque sensor fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 510006 | Drive unit: A magnetic field is disturbing the drive unit. (info) | Keep riding until you are out of the magnetic field. |
| 51000D, 51000E | Drive unit: A magnetic field is disturbing the drive unit. (error, info) | Keep riding until you are out of the magnetic field. Don't restart the bike. |
| 510012 | Drive unit: Torque sensor fault. | Move the bike somewhere else, outdoors if possible, restart and ride for at least 15 seconds. If it persists, see a Bosch eBike dealer. |
| 511001, 511002, 511003, 511004, 51400C, 51400D | Drive unit: Acceleration sensor fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 511006 | Drive unit: Motor assist is limited. (info) | Ride for ten minutes in the lowest mode, then restart. |
| 511102, 511103, 511104, 51400E, 51400F, 514010, 514011 | Drive unit: Position sensor fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 513002 | Drive unit: Cadence sensor fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 513004, 513005 | Drive unit: Cadence sensor fault. | Run an eBike update in the Flow app if one is available, then restart. If it persists, see a Bosch eBike dealer. |
| 513006 | Drive unit: External cadence sensor fault. (warning) | Run an eBike update if available and check the external cadence sensor, its cable and the sensor disc for damage, then restart. If it persists, see a Bosch eBike dealer. |
| 513007 | Drive unit: Brake switch fault. (warning) | Run an eBike update if available, check the brake switch and its cables, pull the brake, then restart. If it persists, see a Bosch eBike dealer. |
| 51301C | Drive unit: Drive unit too hot. | Let the drive unit cool down, restart, and run an eBike update in the Flow app if available. If it persists, see a Bosch eBike dealer. |
| 514001, 514002, 514003, 523003 | Drive unit: Internal speed sensor fault. | Check the rim magnet is fixed firmly on the valve, restart and check the speed display after a short ride. If it persists, see a Bosch eBike dealer. |
| 514008, 530002, 542003, 542004 | Drive unit: Drive unit configured incorrectly. | Dealer job: contact a Bosch eBike dealer. |
| 51400B | Drive unit: Internal speed sensor fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 514012, 514013 | Drive unit: Torque sensor fault. (error, warning) | Update the software in the eBike Flow app, then restart. If it persists, see a Bosch eBike dealer. |
| 515002 | Drive unit: Walk assist can't be activated. (info) | Dealer job: contact a Bosch eBike dealer. |
| 515003 | Drive unit: Walk assist / hill start assist stopped. (info) | Check the drive unit, pedals and wheels turn freely, then start walk assist again. |
| 515004 | Drive unit: Walk assist fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 517001, 517002 | Drive unit: The total distance counter has reached its maximum. (info) | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 517003 | Drive unit: Not a fault: a mileage milestone message. (info) | Nothing to fix; it's a notice. |
| 518001 | Drive unit: No assist modes configured. | Dealer job: contact a Bosch eBike dealer. |
| 518013, 518014, 518015, 518016, 518017, 518018, 518020 | Drive unit: Drive unit not programmed correctly. (error, warning) | Dealer job: contact a Bosch eBike dealer. |
| 518110, 518111, 518112, 518113, 518120, 518121, 518122, 518123, 518130, 518131, 518132, 518133, 523042, 531005 | Drive unit: Drive unit not configured correctly. | Dealer job: contact a Bosch eBike dealer. |
| 522000 | Drive unit: A magnet is disturbing the torque sensor. | Remove any magnet fixed near the drive unit (for example on a pedal or crank), then restart. If it persists, see a Bosch eBike dealer. |
| 523001 | Drive unit: Speed sensor fault. | Check the rim magnet (and spoke magnet if fitted); on Hub Line drives check the drive unit plug. Then restart. If it persists, see a Bosch eBike dealer. |
| 523004 | Drive unit: Speed sensor fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 523005 | Drive unit: The rim magnet's signal is too weak. | Check the rim magnet is fixed on the valve and isn't shielded by the drive unit, then restart. If it persists, see a Bosch eBike dealer. |
| 523006 | Drive unit: Speed sensor fault. | Check the rim magnet (and spoke magnet if fitted), then restart. If it persists, see a Bosch eBike dealer. |
| 524001 | Drive unit: Speed signal tampering detected (tuning). | Remove any tampering and set the magnets correctly. Full assist returns after about 90 minutes of riding in limp-home mode. If it persists, see a Bosch eBike dealer. |
| 525001, 525002, 525003, 525004 | Drive unit: Speed signal tampering detected (tuning). | Make sure nothing on the bike has been tampered with and that the magnets are in the right place. If it persists, see a Bosch eBike dealer. |
| 534001, 534002, 534003, 534004, 534005, 534006, 534007 | Drive unit: Drive unit certificate not valid. | Dealer job: contact a Bosch eBike dealer. |
| 534008, 534009 | Drive unit: Drive unit production fault. | Dealer job: contact a Bosch eBike dealer. |
| 540001 | Drive unit: Drive unit temperature monitoring is switched off. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 542002 | Drive unit: Gear ratio configured incorrectly. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 550001 | Drive unit: The eBike lights are switched off. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 566004 | Drive unit: Safety notice: don't get distracted by the display while riding. (warning) | Nothing to fix; it's a notice. |
| 5F0000, 5F0003 | Drive unit: eBike Lock key not valid. | Deactivate eBike Lock and activate it again in the Flow app. If it persists, see a Bosch eBike dealer. |
| 5F0010, 5F0011, 5F0012, 5F0013, 5F0014, 5F0015, 5F0016, 5F0017, 5F0018, 5F0019, 5F001A, 5F001B, 5F001C, 5F001D, 5F001E | Drive unit: eBike Lock key can't be verified. | Dealer job: contact a Bosch eBike dealer. |
| 5F0060 | Drive unit: Control unit not compatible with eBike Lock. | Dealer job: contact a Bosch eBike dealer. |
| 5F0100, 5F0101 | Drive unit: Drive unit is a pre-production sample. (error, warning) | Dealer job: contact a Bosch eBike dealer. |
| 5F0200 | Drive unit: Control unit not compatible with this eBike. | Update the software in the eBike Flow app, then restart. If it persists, see a Bosch eBike dealer. |
| 610003 | Battery: Battery has been deactivated. | Dealer job: contact a Bosch eBike dealer. |
| 610004 | Battery: Battery configuration error. | Dealer job: contact a Bosch eBike dealer. |
| 610008 | Battery: Battery needs replacing. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 61000D | Battery: Battery software error. | Check the battery and holder contacts for corrosion, clean with a soft damp cloth and let them dry, run an eBike update if available, then restart. If it persists, see a Bosch eBike dealer. |
| 610010 | Battery: Battery software error. (warning) | Run an eBike update in the Flow app if one is available, then restart. If it persists, see a Bosch eBike dealer. |
| 620001, 620005, 620006, 620007, 620008, 620009, 62000A, 62000F, 620010, 620011, 620013 | Battery: Battery current fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 620002, 62000B | Battery: Battery charging current too high. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 620003, 620004, 62000C, 62000D | Battery: Battery discharge current too high. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 62000E | Battery: Battery current flowing in the wrong direction. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 620012 | Battery: Battery fault. | Always switch the bike off before removing or inserting the battery. Restart. If it persists, see a Bosch eBike dealer. |
| 620015 | Battery: Battery current fault. | Check the battery and holder contacts for corrosion, clean and dry them, reinsert the battery, update if available, then restart. If it persists, see a Bosch eBike dealer. |
| 630001, 630002, 630003, 630004, 630005, 630006, 630007, 630008, 630009, 63000B, 63000D, 63000F, 630010, 630012, 640001, 640002, 690080 | Battery: Battery fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 63000C | Battery: The battery's on/off button is stuck down. (warning) | Check the battery's on/off button isn't stuck, then restart. If it persists, see a Bosch eBike dealer. |
| 630011, 630014, 630017, 690077, 6A0008 | Battery: Battery fault. | Run an eBike update in the Flow app if one is available, then restart. If it persists, see a Bosch eBike dealer. |
| 650001 | Battery: Battery fault. | Check the battery is seated and the contacts are free of corrosion (clean and dry them), update if available, then restart. If it persists, see a Bosch eBike dealer. |
| 660001 | Battery: Battery short circuit. | Restart. If it persists, stop using the battery and don't charge it; see a dealer. |
| 660002 | Battery: Internal battery fault. | Take the battery out and connect it to the charger for at least 10 seconds. If LEDs 2 and 4 flash again, unplug it, don't use it and see a dealer. |
| 660003 | Battery: Battery short circuit. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 670001 | Battery: Charging error. | Unplug the charger from the bike and the socket, wait at least 5 seconds and reconnect. Don't plug in while the system is starting or shutting down. |
| 670003 | Battery: More than one battery connected. | Connect all of the bike's components (including removable ones), update the software and restart. If it persists, see a Bosch eBike dealer. |
| 670005 | Battery: The charger is a pre-production sample. (info) | Dealer job: contact a Bosch eBike dealer. |
| 680001, 680004, 680005, 68000A, 68000B, 680010, 680011, 68001B | Battery: Battery temperature measurement fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 680002, 680006, 68000C, 68000D, 680012, 680013, 680014, 680015 | Battery: Battery too cold. | Let the battery warm up somewhere warmer for at least two hours, then restart. If it persists, see a Bosch eBike dealer. |
| 680003, 680008, 68000E, 68000F, 680016, 680019, 68001A, 68001C | Battery: Battery too hot. | Let the battery cool down for at least two hours, then restart. If it persists, see a Bosch eBike dealer. |
| 680007 | Battery: Battery too cold. | Let the battery warm up for at least two hours, then start charging again. If it persists, see a Bosch eBike dealer. |
| 680009 | Battery: Battery too hot to charge. | Let the battery cool down for at least two hours, then start charging again. If it persists, see a Bosch eBike dealer. |
| 680017 | Battery: Battery too hot to charge. | Let the battery cool down for at least two hours, then restart. If it persists, see a Bosch eBike dealer. |
| 68001E, 680101 | Battery: Battery too hot. (warning) | Switch off and let the drive unit cool down for a few minutes, then restart. If it persists, see a Bosch eBike dealer. |
| 690001, 690002, 690003, 690004, 690005, 690006, 690007, 690008, 690009, 69000A, 69000B, 69000C, 69000D, 69000E, 69000F, 690010, 690011, 690012, 690013, 690014, 690015, 690016, 690017, 690018, 690019, 69001C, 69001D, 69001E, 69001F, 690020, 690021, 690022, 690023, 690024, 690025, 690026, 690027, 690028, 690029, 690040, 690041, 690042, 690043, 690044, 690045, 690046, 690047, 690048, 690049, 690060, 690061, 690062, 690063, 690064, 690065, 690066, 690067, 690068, 690069, 690070, 690071, 690072, 690073, 690074, 690075, 690078, 690079 | Battery: Battery voltage fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 690076 | Battery: Battery voltage fault. | Use only the original Bosch charger, then restart. If it persists, see a Bosch eBike dealer. |
| 690100 | Battery: Battery charge is low. (warning) | Charge the battery. |
| 690101 | Battery: Battery charge is very low. (warning) | Charge the battery. |
| 690102 | Battery: Energy Reserve mode is active: the battery is nearly empty and assist is limited. (warning) | Charge the battery. |
| 690300 | Battery: Battery deeply discharged. | Update the software in the eBike Flow app, then restart. If it persists, see a Bosch eBike dealer. |
| 6A0000 | Battery: Battery software too old for DualBattery use. (critical error) | Connect all of the bike's components (including removable ones), update the software and restart. If it persists, see a Bosch eBike dealer. |
| 6A0001 | Battery: More than two batteries connected. | Remove the extra batteries. |
| 6A0002 | Battery: A non-Bosch battery is connected. | Remove any third-party batteries; use only original Bosch batteries. |
| 6A0004 | Battery: This eBike doesn't support the PowerMore range extender. (critical error) | Remove the PowerMore battery, then restart. If it persists, see a Bosch eBike dealer. |
| 6A0005 | Battery: This eBike doesn't support DualBattery. (warning) | Update the software in the eBike Flow app, then restart. If it persists, see a Bosch eBike dealer. |
| 6A0006 | Battery: Battery fault (DualBattery). | Update the software in the eBike Flow app, then restart. If it persists, see a Bosch eBike dealer. |
| 6A0007 | Battery: The two batteries of a DualBattery setup can't both be charged. | Update the software in the eBike Flow app, then restart. If it persists, see a Bosch eBike dealer. |
| 6F0200, 6F0203 | Battery: eBike Lock key not valid. | Deactivate eBike Lock and activate it again in the Flow app. If it persists, see a Bosch eBike dealer. |
| 100004 | Control unit: Certificate of the drive unit has expired. (warning) | Dealer job: contact a Bosch eBike dealer. |
| 100005 | Control unit: Certificate of the battery has expired. (warning) | Dealer job: contact a Bosch eBike dealer. |
| 100006 | Control unit: Certificate of the on-board computer has expired. (warning) | Dealer job: contact a Bosch eBike dealer. |
| 100007 | Control unit: Certificate of the ConnectModule has expired. (warning) | Dealer job: contact a Bosch eBike dealer. |
| 100008 | Control unit: Certificate of the ABS has expired. (warning) | Dealer job: contact a Bosch eBike dealer. |
| 100009 | Control unit: Drive unit certificate not valid. | Dealer job: contact a Bosch eBike dealer. |
| 10000A | Control unit: Certificate of the battery is not valid. | Dealer job: contact a Bosch eBike dealer. |
| 10000B | Control unit: Certificate of the on-board computer is not valid. | Dealer job: contact a Bosch eBike dealer. |
| 10000C | Control unit: Certificate of the ConnectModule is not valid. | Dealer job: contact a Bosch eBike dealer. |
| 10000D | Control unit: Certificate of the ABS is not valid. | Dealer job: contact a Bosch eBike dealer. |
| 10000E | Control unit: Certificate of the control unit is not valid. | Dealer job: contact a Bosch eBike dealer. |
| 110001 | Control unit: Control unit fault. | Update the software in the eBike Flow app, then restart. If it persists, see a Bosch eBike dealer. |
| 112000 | Control unit: Phone connection failed. | Log in to the app again and reconnect the phone; if that fails, reinstall the app and pair again. If it persists, see a Bosch eBike dealer. |
| 112002 | Control unit: Control unit configuration error. | Dealer job: contact a Bosch eBike dealer. |
| 112100 | Control unit: Control unit communication error. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 113101, 113102, 113103, 113104, 113111 | Control unit: Control unit memory error. (critical error, error) | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 113113 | Control unit: Control unit memory error. | Start the software update again. If it persists, see a Bosch eBike dealer. |
| 113114 | Control unit: Control unit memory error. | Dealer job: contact a Bosch eBike dealer. |
| 113120 | Control unit: Control unit software error. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 113121 | Control unit: No phone connected. (warning) | Connect your phone to the control unit again. |
| 113150 | Control unit: The date set is too far in the past. | Pick a date no more than a week in the past. |
| 116000 | Control unit: ABS not detected. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 116001 | Control unit: This eBike isn't compatible with the ABS fitted. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 120107 | Control unit: USB charging not working. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 120109 | Control unit: Control unit LEDs not working. (critical error) | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 120111, 142002 | Control unit: Control unit power supply fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 120113 | Control unit: Control unit ambient light sensor not working. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 131000 | Control unit: Control unit buttons stuck down. | Check the control unit buttons aren't stuck, then restart. If it persists, see a Bosch eBike dealer. |
| 133000, 133001 | Control unit: Control unit temperature sensor fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 133002 | Control unit: Control unit temperature monitoring fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 135000 | Control unit: Control unit brightness sensor not working. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 136001 | Control unit: Internal control unit fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 141000 | Control unit: Control unit internal battery fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 141001 | Control unit: The control unit's internal battery is flat. (warning) | Charge the control unit's internal battery for at least 45 minutes, from the bike charger or a power bank. It also charges while you ride. |
| 141200 | Control unit: The control unit's internal battery may be faulty. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 142003 | Control unit: The battery was removed while the bike was switched on. (warning) | Only remove the battery with the bike switched off. If it persists, check the battery is seated and the display and remote cables are plugged in, then restart. If it persists, see a Bosch eBike dealer. |
| 144000, 144001 | Control unit: The control unit can't be charged. (error, warning) | Charge the control unit with a different power bank or charger. |
| 144010 | Control unit: Moisture in the USB port. (info) | Let the USB port dry out and keep its cap closed when nothing is plugged in. |
| 144020 | Control unit: Too much power drawn from the USB port. (warning) | Unplug the USB cable and check the connected device and cable for damage. |
| 144030 | Control unit: USB charging switched off because too much power was drawn. (warning) | Reduce the load (for example switch off the high beam, unplug USB devices), then restart to re-enable USB charging. If it persists, see a Bosch eBike dealer. |
| 152001, 153001 | Control unit: Control unit too hot. | Let the eBike cool for about 15 minutes somewhere cooler, out of the sun, then restart. If it persists, see a Bosch eBike dealer. |
| 152002, 153002 | Control unit: Control unit too hot. (error, warning) | Let the eBike cool for about ten minutes somewhere cooler, out of the sun. |
| 153004 | Control unit: Incompatible on-board computer connected. | Dealer job: contact a Bosch eBike dealer. |
| 153012 | Control unit: Control unit too hot. (warning) | Let the eBike cool for about ten minutes somewhere cooler, out of the sun, and unplug USB devices. |
| 1B0003 | Control unit: Can't connect to the cordless remote. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 1B7210, 1B7212, 1B7610, 1B7612, 1B7710, 1B7712, 1C7410, 1C7412, 1C7510, 1C7512, 1C7710 | Control unit: Can't connect to the electronic gearbox / gear hub. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 1B7211, 1B7611, 1B7711, 1C7411, 1C7511, 1C7711 | Control unit: Connection to the electronic gearbox / gear hub lost. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 1B7213, 1B7613, 1B7713, 1C7413, 1C7513, 1C7713 | Control unit: Control unit software not compatible with the electronic gearbox. | Update the software in the eBike Flow app, then restart. If it persists, see a Bosch eBike dealer. |
| 1B7214 | Control unit: More than one electronic gearbox connected. | Remove the second electronic gearbox, then restart. If it persists, see a Bosch eBike dealer. |
| 1B7614, 1B7714, 1C7414, 1C7514, 1C7714 | Control unit: More than one electronic gearbox connected. | Remove the extra electronic gearbox, then restart. If it persists, see a Bosch eBike dealer. |
| 1B7910, 1B7912 | Control unit: Can't connect to the electronic shifting. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 1B7911 | Control unit: Connection to the electronic shifting lost. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 1B7913 | Control unit: Control unit software not compatible with the electronic shifting. | Run an eBike update in the Flow app if one is available, then restart. If it persists, see a Bosch eBike dealer. |
| 1B7914 | Control unit: More than one electronic shifting system connected. | Remove the extra electrical wiring, then restart. If it persists, see a Bosch eBike dealer. |
| 1C8010, 1C8012 | Control unit: Can't connect to the ABS. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 1C8011 | Control unit: Connection to the ABS lost. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 1C8013 | Control unit: Control unit software not compatible with the ABS. | Update the software in the eBike Flow app, then restart. If it persists, see a Bosch eBike dealer. |
| 1C9000 | Control unit: Can't connect to the electronic dropper seatpost. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 1C9001 | Control unit: Connection to the electronic dropper seatpost lost. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 1C9002 | Control unit: Control unit software not compatible with the dropper seatpost. | Update the software in the eBike Flow app, then restart. If it persists, see a Bosch eBike dealer. |
| 1C9005 | Control unit: Dropper seatpost software out of date. | Update the seatpost in its manufacturer's app, then restart. If it persists, see a Bosch eBike dealer. |
| 1F0200 | Control unit: No on-board computer (display) connected. | Connect an on-board computer. If it persists, see a Bosch eBike dealer. |
| 1B0001 | Display: Cordless display/remote battery is low. (warning) | Replace the battery of the cordless control unit. |
| 1B0002 | Display: Can't connect to the cordless display. | Pair the cordless unit again in the eBike Flow app, then restart. If it persists, see a Bosch eBike dealer. |
| 411002 | Display: Safety notice: don't get distracted by the display while riding. (warning) | Nothing to fix; it's a notice. |
| 420001 | Display: On-board computer too cold. (warning) | Take the on-board computer (or the bike) somewhere warmer. |
| 420002, 430006 | Display: On-board computer too hot. (error, warning) | Let the on-board computer cool for at least 15 minutes somewhere colder, out of the sun, then restart. If it persists, see a Bosch eBike dealer. |
| 430013 | Display: eBike Lock key not valid. | Restart, then deactivate and reactivate eBike Lock in the Flow app. If it persists, see a Bosch eBike dealer. |
| 434004, 434304, 440001 | Display: On-board computer software error. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 1C9021 | eBike: Error reported by the electronic dropper seatpost. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 1C9022 | eBike: Warning from the electronic dropper seatpost. (warning) | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 1C9023 | eBike: Information message from the electronic dropper seatpost. (info) | Contact the seatpost manufacturer or your dealer. |
| F00001 | eBike: Pre-production components detected. (warning) | Dealer job: contact a Bosch eBike dealer. |
| F00002 | eBike: A system certificate has expired. (warning) | Dealer job: contact a Bosch eBike dealer. |
| F10001 | eBike: An eBike software update is available. (info) | Connect all of the bike's components, including removable ones, and run the update in the Flow app (bike must be registered). |
| F10002 | eBike: A software fix or improvement is available. (warning) | Acknowledge the warning, run the software update and restart. |
| F10003, F10004, F10005 | eBike: Component software versions don't match. (critical error, error) | Connect all of the bike's components (including removable and optional ones), then run an eBike update in the Flow app (the bike must be registered). If it persists, see a Bosch eBike dealer. |
| 900001 | ConnectModule: ConnectModule runs pre-production software. (warning) | Dealer job: contact a Bosch eBike dealer. |
| 900002, 900003 | ConnectModule: ConnectModule is a pre-production sample. (warning) | Dealer job: contact a Bosch eBike dealer. |
| 90000A, 90000B | ConnectModule: ConnectModule too hot. | Let the eBike cool for at least 15 minutes somewhere colder, out of direct sun, then restart. If it persists, see a Bosch eBike dealer. |
| 902005, 902006, 902007 | ConnectModule: ConnectModule mobile network not working. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 902008, 902009, 90200B, 90200C | ConnectModule: ConnectModule not responding. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 90200D, 902010, 902012, 902013, 902014, 9F0104 | ConnectModule: ConnectModule software update failed. | Restart and, if possible, repeat the software update in the Flow app. If it persists, see a Bosch eBike dealer. |
| 903001, 903003, 903004, 903006, 903007, 903008, 903009, 90300A, 90300B | ConnectModule: ConnectModule data connection failed. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 903002, 903005 | ConnectModule: ConnectModule can't reach the Bosch server. | Move the bike somewhere with better mobile reception. If it persists, see a Bosch eBike dealer. |
| 90400A, 90400B, 90400C | ConnectModule: ConnectModule temperature monitoring fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 905001, 905002, 905003, 905004 | ConnectModule: ConnectModule power supply fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 905005 | ConnectModule: ConnectModule battery too hot. | Let the eBike cool for at least 15 minutes somewhere colder, out of direct sun, then restart. If it persists, see a Bosch eBike dealer. |
| 905006 | ConnectModule: ConnectModule battery fault. | Dealer job: contact a Bosch eBike dealer. |
| 905007 | ConnectModule: ConnectModule battery defective. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 905008, 905009 | ConnectModule: ConnectModule battery fault. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 90500A | ConnectModule: ConnectModule battery fault. | Leave the eBike switched on for at least 45 minutes so the ConnectModule battery can charge. |
| 90500E | ConnectModule: ConnectModule battery almost flat and not charging. (warning) | Charge the eBike at room temperature for at least two hours, then ride for 30 minutes with assist. If it persists, see a Bosch eBike dealer. |
| 906001, 906002, 906003, 906004, 907001, 907002 | ConnectModule: ConnectModule memory error. | Restart the eBike. If it persists, see a Bosch eBike dealer. |
| 907003 | ConnectModule: ConnectModule production fault. | Dealer job: contact a Bosch eBike dealer. |
| 908004 | ConnectModule: ConnectModule registration failed. (warning) | Dealer job: contact a Bosch eBike dealer. |
| 1BF000 | Heart rate monitor: Heart-rate sensor battery almost flat. (warning) | Charge or replace the heart-rate sensor battery. |
| 1BF001 | Heart rate monitor: No connection to the heart-rate sensor. (warning) | Connect the heart-rate sensor to the control unit again. |
- First step for nearly every code: switch off, wait, restart without pedalling.
- Look the exact 6-character code up in the eBike Flow app or the Bosch eBike Help Center, which give the official meaning and remedy.
- Speed-sensor/magnet codes (503xxx/504xxx/523001) are the most common rider-fixable faults: check the magnet distance and that nothing has been tampered with.
- Keep the system software current via eBike Flow (OTA).
Written in our own words from the manufacturer’s documentation. Codes can change with firmware; your dealer’s diagnostic software has the final word. Sources: help.bosch-ebike.com
FAQ
What does Bosch 514001, mean?
Drive unit: Internal speed sensor fault. What to do: Check the rim magnet is fixed firmly on the valve, restart and check the speed display after a short ride. If it persists, see a Bosch eBike dealer.
What does Bosch 50100A, mean?
Drive unit: Drive unit too hot. (error, warning) What to do: Switch off and let the drive unit cool down for a few minutes, then restart. If it persists, see a Bosch eBike dealer.
How do I avoid Bosch error codes?
First step for nearly every code: switch off, wait, restart without pedalling. Look the exact 6-character code up in the eBike Flow app or the Bosch eBike Help Center, which give the official meaning and remedy. Speed-sensor/magnet codes (503xxx/504xxx/523001) are the most common rider-fixable faults: check the magnet distance and that nothing has been tampered with. Keep the system software current via eBike Flow (OTA).
Motors: Bosch Performance Line CX-R, Bosch Performance Line CX Race, Bosch Performance Line CX, Bosch Performance Line SX, Bosch Performance Line PX. Bosch firmware updates. Other systems: Bosch classic (Gen 2 to 4), Shimano STEPS / EP, DJI Avinox, TQ HPR, Fazua Ride 60, Specialized Turbo, Yamaha PW, Giant SyncDrive.