Shimano STEPS / EP error codes
All 113 Shimano STEPS / EP codes we have documented: what each one means, what stops working and what you can do yourself before going to a dealer. Applies to EP8/EP801, EP6/EP600, E-series.
Error codes 'E***' and warning codes 'W***' on the cycle computer screen (e.g. SC-EM800, SC-EN600); newer firmware can show 5-digit variants (e.g. W10000, E01000). Shimano's official code lookup is si.shimano.com/en/error.
Get Shimano news & firmware updates in TelegramError codes (60)
| Code | Meaning | What to do |
|---|---|---|
| E010 | Fault detected in the drive unit. No assist. | Switch the system off and on again. If it keeps coming back, stop riding and take the bike to your dealer. |
| E01000-E01004 | Sensor fault inside the drive unit. No assist. | Dealer job: the drive unit needs to be checked by a Shimano dealer or distributor. |
| E01010, E01011 | Sensor fault inside the drive unit. No assist. | Dealer job: have the drive unit checked. |
| E01020-E01022 | Sensor fault inside the drive unit. No assist. | Dealer job: have the drive unit checked. |
| E01030 | A sensor in the drive unit has failed. No assist. | Dealer job: have the drive unit checked. |
| E01040-E01042 | Fault in the drive unit's motor. No assist. | Dealer job: have the drive unit checked. |
| E01050, E01051 | A sensor in the drive unit has failed. No assist. | Dealer job: have the drive unit checked. |
| E011 | General system error. No assist. | Switch the system off and on again. |
| E012 | The torque sensor could not initialise properly. No assist. | Restart the system with your feet off the pedals. If it persists, the dealer should check chain tension; after that the distributor. |
| E013 | Problem with the drive unit firmware. No assist. | Dealer job: connect to E-TUBE PROJECT and restore the firmware. |
| E014 | Implausible speed signal from the speed sensor. No assist. | Dealer job: refit the speed sensor and magnet in the correct positions. If the bike has been modified (speed tuning), undo it and restart. |
| E015 | Fault detected in the drive unit. No assist. | Switch the system off and on again. If it keeps coming back, stop riding and take the bike to your dealer. |
| E01500 | Communication error between the microcontrollers inside the drive unit. No assist. | Switch the system off and on again. If it persists, the dealer should read the drive unit error log in E-TUBE PROJECT and send a report to the distributor. |
| E020 | Communication error between battery and drive unit. No assist. | Dealer job: check the cable between drive unit and battery and the power cord. |
| E02000 | Communication error between battery and drive unit. No assist. | Dealer job: check the cable between drive unit and battery and the power cord. |
| E021 | The battery meets the system standard but is not supported by this drive unit. No assist. | Switch the system off and on again. |
| E022 | The battery does not meet the system standard. The system won't start. | Switch the system off and on again. |
| E023 | Electrical fault in the battery. The system won't start. | Switch the system off and on again. |
| E024 | Battery overcurrent protection has tripped (communication error with the bike system). The system won't start. | Dealer job: check for loose or badly seated cables. |
| E025 | The battery can't find the drive unit: non-genuine drive unit or disconnected power cord. The system won't start. | Dealer job: fit a genuine battery or drive unit and check the power cord. |
| E030 | The shifting unit fitted doesn't match the system configuration. No assist. | Dealer job: update the configuration in E-TUBE PROJECT. |
| E031 | Chain tension not adjusted, or the crank is not fitted in the correct position. No assist. | Dealer job: adjust chain tension, refit the crank in the specified orientation and switch on again. |
| E033 | The installed firmware isn't supported by this system. No assist. | Dealer job: update firmware on all SHIMANO STEPS units to the latest version in E-TUBE PROJECT. |
| E034 (E013) | Problem with the drive unit firmware. No assist. | Dealer job: restore the firmware in E-TUBE PROJECT. |
| E03400 | Problem with the drive unit firmware. No assist. | Dealer job: restore the firmware in E-TUBE PROJECT. |
| E035 | Problem with the bike settings stored in the system. No assist. | Dealer job: check the configuration in E-TUBE PROJECT and correct it if it doesn't match the bike. |
| E03500 | Problem with the bike settings stored in the system. No assist. | Dealer job: check the configuration in E-TUBE PROJECT. |
| E043 | Part of the unit's firmware may be corrupted. No assist. | Dealer job: the firmware has to be restored. |
| E044 | Error caused by the system configuration. No assist. | Contact the bike manufacturer. |
| E050 (E014) | Implausible speed signal from the speed sensor. No assist. | Dealer job: refit speed sensor and magnet correctly; undo any speed tuning and restart. |
| E05000 | Implausible speed signal from the speed sensor. No assist. | Dealer job: refit speed sensor and magnet correctly; undo any speed tuning and restart. |
| E201 | Fault detected in the drive unit. No assist. | Switch the system off and on again. If it keeps coming back, stop riding and take the bike to your dealer. |
| E203 | Fault detected in the drive unit. No assist. | Update the drive unit firmware if it's not the latest. If it keeps coming back, stop riding and take the bike to your dealer. |
| E206 | Fault detected in the drive unit (overheating). No assist. | Switch off and let the motor cool in the shade before switching on again. If it keeps coming back, stop riding and take the bike to your dealer. |
| E209 | Fault detected in the drive unit. No assist. | Stop riding and take the bike to your dealer. |
| E229 | Fault on the drive unit's CAN port. Units connected via CAN won't work properly. | Stop riding and take the bike to your dealer. |
| E239 | Fault on the drive unit's accessory power port. Lights and accessories won't work properly. | The accessory port needs checking: take the bike to your dealer. |
| E254 | Electrical fault in the battery. The system won't start. | Check the power cord is connected; then press and hold the battery power button; then charge the battery. If none of that helps, see your dealer. |
| E255 | Electrical fault in the battery. The system won't start. | Check that drive unit and battery are compatible. If they are, press the battery power button several times; if that fails, contact a distributor. |
| E259 | Electrical fault in the battery. The system won't start. | Stop riding and take the bike to your dealer. |
| E295 | Implausible speed signal from the speed sensor. No assist. | Check speed sensor and magnet are fitted correctly and undo any modifications, then restart. Otherwise the drive unit may go into Safe Mode (E299). |
| E299 | The drive unit has gone into Safe Mode because tampering (for example speed tuning) was detected. No assist. | Stop riding and take the bike to your dealer. |
| E401 | Fault in the rear derailleur or its motor unit. The derailleur won't work. | Unplug and reconnect the electric wire or battery. If it persists, see your dealer. |
| E503 | Electrical fault in the freehub. No system functions. | If it happens repeatedly, contact your dealer. |
| E504 | Electrical fault in the freehub. | If it happens repeatedly, contact your dealer. |
| E505 | Fault in the freehub sensor. Automatic shifting won't work. | If it happens repeatedly, contact your dealer. |
| E608 | Problem with the drive unit firmware. The E-BIKE system lock can't be released. | Stop riding and take the bike to your dealer; the firmware has to be restored. |
| E609 | Fault detected in the drive unit. The system won't start. | Stop riding and take the bike to your dealer. |
| E814 | Communication fault between units. No system functions. | Dealer job: check that electric wires and the power cable are seated and undamaged. |
| E903 | Units have mismatched settings. No assist. | Stop riding and take the bike to your dealer. |
| E905 | Incompatible combination of units. No system functions. | Check compatibility in E-TUBE PROJECT and fit compatible units. |
| E906 | Communication fault between units. No system functions. | Stop riding and take the bike to your dealer. |
| E910 | Incompatible combination of units. No system functions. | Fit compatible units; ask your dealer if unsure. |
| E914 | Fault between drive unit and battery. No assist. | Clean the contacts on the battery mount and reinsert the battery. If it persists, see your dealer. |
| E915 | Drive unit and battery are not compatible. The system won't start. | Stop riding and take the bike to your dealer. |
| E916 | Fault detected in the drive unit. No assist. | Stop riding and take the bike to your dealer. |
| E925 | Battery and charger are not compatible. The battery won't charge. | Use a compatible charger. |
| E934 | Communication error between the display (cycle computer) and the drive unit. No assist. | Reconnect the wire between display and drive unit. The code clears after switching off, but if the restriction remains, see your dealer. |
| E944 | Communication error between the shifter/switch and the drive unit. No assist. | Reconnect the wire between switch and drive unit. If the restriction remains after a restart, see your dealer. |
| E973 | Freehub and rear derailleur settings don't match. No system functions. | Update the configuration in E-TUBE PROJECT. If it persists, see your dealer. |
Warning codes (51)
| Code | Meaning | What to do |
|---|---|---|
| W010 | The drive unit is too hot. Reduced assist. | Ride without assist until the motor cools down. If it persists, see your dealer. |
| W011 | No speed signal from the speed sensor. Assist cuts out at a lower speed than normal. | Dealer job: refit the speed sensor and the magnet (often moved when the brake rotor was changed). |
| W012 | The crank may be fitted the wrong way round. | Dealer job: refit the crank in the specified orientation and switch on again. |
| W013 | The torque sensor could not initialise properly. Reduced assist. | Restart the system with your feet off the pedals. If it persists, see your dealer. |
| W020 | Battery temperature is outside its operating range, so output has stopped. The system won't start. | Too hot: let the battery cool in the shade. Too cold: bring it indoors to warm up. |
| W030 | More than one assist switch is connected. Gear shifting doesn't work. | Reassign one switch as a shift switch in E-TUBE PROJECT, or connect only one assist switch and restart. |
| W031 | Chain tension not adjusted, or the crank is not fitted correctly. No assist. | Dealer job: adjust chain tension and refit the crank. |
| W032 | The shifting unit fitted doesn't match the system configuration. Gear shifting doesn't work. | Dealer job: check the system in E-TUBE PROJECT and fit the configured shifting unit. |
| W10000 (W010) | The drive unit is too hot. Reduced assist. | Ride without assist until the motor cools down. |
| W10100 (W011) | No speed signal from the speed sensor. Assist cuts out at a lower speed than normal. | Dealer job: refit speed sensor and magnet. |
| W103 | The torque sensor could not initialise properly. Reduced assist. | Turn the cranks backwards two or three times. If it persists, see your dealer. |
| W10300 | The torque sensor could not initialise properly. Reduced assist. | If the display shows W103, turn the cranks backwards two or three times; if it shows W013, restart with feet off the pedals. |
| W10600 | The torque sensor could not initialise properly. No assist. | Restart with your feet off the pedals, repeating until it clears; riding on may also clear it. Otherwise the dealer adjusts chain tension and runs the spin-up calibration (rear wheel lifted, 10-20 km/h, stop and start the cranks a few times). |
| W20000 (W020) | The system switched off because the battery temperature was out of range. The system won't start. | Let a hot battery cool in the shade, or warm a cold one indoors. |
| W30200 (W032) | The shifting unit fitted doesn't match the system configuration. Gear shifting doesn't work. | Dealer job: check the system in E-TUBE PROJECT. |
| W203 | The wireless unit's firmware version isn't supported. Wireless functions are limited. | Take the bike to your dealer; the firmware has to be restored. |
| W204 | Communication error between the wireless unit and the drive unit. The system won't start. | The connection between drive unit and wireless unit needs checking: see your dealer. |
| W205 | The torque sensor could not initialise properly. Reduced assist. | Turn the cranks backwards two or three times. If it persists, see your dealer. |
| W206 | Fault in the drive unit (temperature). Reduced assist. | Assist returns to normal once the motor is back in its normal temperature range. If it keeps happening, see your dealer. |
| W207 | Ride data could not be updated correctly. The latest ride data isn't shown. | Switch the battery off and on again. |
| W208 | The torque sensor could not initialise properly. No assist. | Restart with your feet off the pedals, repeating until it clears; riding on may also clear it. Otherwise the dealer adjusts chain tension and runs the spin-up calibration. |
| W209 | Ride data can't be updated. The warning stays on. | Take the bike to your dealer. |
| W222 | Fault on the drive unit's CAN port. Units connected via CAN won't work properly. | The CAN port needs checking: see your dealer. |
| W232 | Fault on the drive unit's accessory power port. Accessories won't work properly. | The accessory port needs checking: see your dealer. |
| W233 | Accessory power cut because the drive unit is too hot. Lights and accessories don't work. | Power returns once the motor cools down. If it keeps happening, see your dealer. |
| W240 | Fault detected in the drive unit. CAN devices may not communicate properly. | Switch the system off and on again. If it keeps coming back, stop riding and take the bike to your dealer. |
| W242 | Fault on the drive unit's light port. Lights and accessories won't work properly. | The light port needs checking: see your dealer. |
| W243 | Fault on the power port of a CAN unit. Units connected via CAN won't work properly. | Have the CAN unit power port checked by your dealer. |
| W244 | Power to a CAN device has been cut. The CAN device doesn't communicate. | Switch the system off and on again. If it persists, stop using that device and see your dealer. |
| W256 | The system switched off because the battery temperature was out of range. The system won't start. | Cool a hot battery in the shade or warm a cold one indoors, then switch it on. If it persists, see your dealer. |
| W292 | No speed signal from the speed sensor. Assist cuts out at a lower speed than normal. | Check speed sensor and magnet are fitted correctly and undo any modifications. |
| W309 | Firmware error in the display (cycle computer). The display firmware can't be updated. | Take the bike to your dealer. |
| W359 | Firmware error in the switch unit. The switch firmware can't be updated. | Take the bike to your dealer. |
| W401 | Fault in the rear derailleur or its motor unit. The derailleur doesn't work. | Unplug and reconnect the electric wire or battery. If it persists, see your dealer. |
| W409 | Firmware error in the rear derailleur. The derailleur firmware can't be updated. | Take the bike to your dealer. |
| W606 | Problem with the drive unit firmware. Some drive unit settings can't be changed. | Take the bike to your dealer; the firmware has to be restored. |
| W607 | Problem with the drive unit firmware. The drive unit firmware can't be updated. | Take the bike to your dealer. |
| W617 | Firmware error in the wireless unit. The wireless unit firmware can't be updated. | Take the bike to your dealer. |
| W902 | Power from the PC to the e-bike system has stopped. E-TUBE PROJECT Professional connection is limited. | Switch the system off and on again. Then check the USB unit to PC connection. If it persists, see your dealer. |
| W905 | Fault in the USB unit connector; water detected in the USB port. Charging is limited. | Switch the system off and on again. Dry the USB connector with a clean lint-free cloth. If it persists, see your dealer. |
| W906 | The USB unit is too hot. Charging is limited. | Charging resumes once it cools. Check the connected USB device. If it keeps happening, see your dealer. |
| W908 | Firmware error in the USB unit. No connection to E-TUBE PROJECT. | Take the bike to your dealer; the firmware has to be restored. |
| W909 | Firmware error in the USB unit. The USB unit firmware can't be updated. | Take the bike to your dealer. |
| W935 | Communication error between the display (cycle computer) and the drive unit. Display functions don't work. | Reconnect the wire between display and drive unit. If the restriction remains after a restart, see your dealer. |
| W945 | Communication error between the shifter/switch and the drive unit. Switch functions don't work. | Reconnect the wire between switch and drive unit. If it persists, see your dealer. |
| W954 | Communication error between the rear shifting unit and the drive unit. Rear shifting doesn't work. | Reconnect the wire between rear shifting unit and drive unit. If it persists, see your dealer. |
| W960 | Communication error between a CAN device and the drive unit. The CAN device doesn't communicate. | Switch the system off and on again. If it keeps coming back, stop riding and take the bike to your dealer. |
| W965 | Drive unit and CAN device are not compatible. The CAN device doesn't communicate. | Fit a compatible CAN device; ask your dealer if unsure. |
| W966 | Drive unit and CAN device are not compatible. The CAN device doesn't communicate. | Update the drive unit firmware to the latest version. If it keeps coming back, stop riding and take the bike to your dealer. |
| W967 | The E-BIKE system lock is engaged. Assist and electronic shifting are restricted. | Release the system lock (app or key). Ask your dealer if you don't know how. |
| W969 | Firmware error in the CAN unit. The CAN unit firmware can't be updated. | Take the bike to your dealer. |
- W-codes are warnings that usually clear on their own; E-codes stop assist and usually need a restart or dealer.
- Never power on while pressing on a pedal (triggers W013).
- Keep all components on matching firmware via E-TUBE PROJECT Cyclist.
Written in our own words from the manufacturer’s documentation. Codes can change with firmware; your dealer’s diagnostic software has the final word. Sources: si.shimano.com · merida-bikes.com · manualslib.com
FAQ
What is the difference between Shimano E and W codes?
Codes starting with W are warnings: the bike usually keeps working with reduced assist or a limited function, and many clear by themselves. E codes are errors: assist usually stops until the cause is fixed, often with a restart, sometimes only by a dealer.
What does Shimano E014 mean?
Implausible speed signal from the speed sensor. No assist. What to do: Dealer job: refit the speed sensor and magnet in the correct positions. If the bike has been modified (speed tuning), undo it and restart.
What does Shimano W010 mean?
The drive unit is too hot. Reduced assist. What to do: Ride without assist until the motor cools down. If it persists, see your dealer.
What does Shimano E013 mean?
Problem with the drive unit firmware. No assist. What to do: Dealer job: connect to E-TUBE PROJECT and restore the firmware.
How do I avoid Shimano error codes?
W-codes are warnings that usually clear on their own; E-codes stop assist and usually need a restart or dealer. Never power on while pressing on a pedal (triggers W013). Keep all components on matching firmware via E-TUBE PROJECT Cyclist.
Motors: Shimano EP810 / EP801 / EP6. Shimano firmware updates. Other systems: Bosch Smart System, Bosch classic (Gen 2 to 4), DJI Avinox, TQ HPR, Fazua Ride 60, Specialized Turbo, Yamaha PW, Giant SyncDrive.