DJI Avinox errors and warnings
How DJI Avinox reports faults and what to do in each situation, from the display warnings and the startup health check to charger lights and pairing problems: what each one means, what stops working and what you can do yourself before going to a dealer. Applies to M1, M2, M2S.
Avinox shows warnings as text on the control display rather than public numeric codes. Details and the suggested fix are under Settings, System Status on the display; logs can be exported from the Avinox Ride app for the bike manufacturer.
Get DJI Avinox news & firmware updates in Telegram| Message / situation | Meaning | What to do |
|---|---|---|
| Pop-up warning at switch-on (with beep) | The automatic health check that runs every time the system starts has found a fault. | Open the Avinox Ride app: it shows the detailed fault status and self-diagnosis tips. On the display, Settings, System Status shows the warning details too. If it persists, contact your dealer or the bike manufacturer. |
| Warning on the control display while riding | The drive system has detected a problem during the ride. Avinox doesn't publish a public list of numeric codes. | Swipe up on the display, open Settings, then System Status for the details and the suggested fix. If it persists, contact your dealer or the bike manufacturer. |
| Display error code + alarm (screen temperature) | The temperature sensor under the screen has measured an abnormal temperature. A warm display is normal: the screen and GPS module produce heat and it absorbs sunlight. | Get the bike out of direct sun and let the display cool down before riding on. If it persists, contact your dealer or the bike manufacturer. |
| No assist outside -10 to 40 °C | The drive system is designed to work between -10 and 40 °C ambient temperature. | Let the bike warm up or cool down to within that range, then restart. |
| Bike won't start, no assist (anti-theft mode) | Anti-theft mode has been switched on remotely in the app: the system is locked and assist is off. Moving the bike sets off an alarm and, on 4G bikes, sends a notification. | Unlock the bike in the Avinox Ride app (owner account). |
| Prompt to switch batteries | The active battery has a fault (dual-battery setups with a secondary battery). | Switch to the other battery when prompted. This turns Auto Switch off; have the faulty battery checked. If it persists, contact your dealer or the bike manufacturer. |
| Charger LED yellow | Solid yellow with no battery connected means standby and is normal. Solid or flashing yellow (or no light) while connected to the battery means the charger has gone into a protection state. | If it shows while charging, stop charging immediately and contact your dealer. Use only the original charger. |
| Charger LED red / green | Red: the battery is charging. Green: fully charged. | Nothing to fix. Unplug once it's full. |
| Battery won't charge (temperature) | The battery charges only between 0 and 40 °C. Charging a hot battery straight after a ride also shortens its life. | Let the battery reach room temperature first, then charge. |
| Phone won't pair with the bike | Usually the bike is still paired with another account or phone, an old Bluetooth pairing wasn't cleared, the prompt wasn't confirmed, or the app lacks Bluetooth permission. | Unpair from the old account or phone, forget the bike in the phone's Bluetooth settings, confirm the prompt on both phone and display, allow Bluetooth for the app and restart bike and Bluetooth. One account can only pair one bike at a time. If it persists, contact your dealer or the bike manufacturer. |
| Wireless controller won't pair | The left or right wireless controller has lost its pairing with the drive system. | Hold both buttons on that controller for five seconds until its light flashes fast, then pair again. |
| System crash or repeated errors | A fault the display can't resolve, or the system restarts during a ride. | In the Avinox Ride app go to Help, Support, Drive System Errors and export the log for the bike manufacturer to analyse. |
| Water in the battery | Liquid has got into the battery (battery IP56, drive unit IP66). | Don't use or charge the battery again; contact the bike manufacturer. |
- Read the warning in Settings > System Status on the display.
- If the issue persists, contact the bike manufacturer (not DJI directly) and export the drive-system log from the Avinox Ride app.
- Keep firmware updated through the app.
Written in our own words from the manufacturer’s documentation. Codes can change with firmware; your dealer’s diagnostic software has the final word. Sources: dl.avinox-ebike.com · avinox-ebike.com
FAQ
Does DJI Avinox have numeric error codes?
DJI Avinox does not publish a public list of numeric error codes. Faults appear as warnings on the display and in the app, which also suggest a fix. Avinox shows warnings as text on the control display rather than public numeric codes. Details and the suggested fix are under Settings, System Status on the display; logs can be exported from the Avinox Ride app for the bike manufacturer.
How do I avoid DJI Avinox error codes?
Read the warning in Settings > System Status on the display. If the issue persists, contact the bike manufacturer (not DJI directly) and export the drive-system log from the Avinox Ride app. Keep firmware updated through the app.
Motors: DJI Avinox. DJI Avinox firmware updates. Other systems: Bosch Smart System, Bosch classic (Gen 2 to 4), Shimano STEPS / EP, TQ HPR, Fazua Ride 60, Specialized Turbo, Yamaha PW, Giant SyncDrive.