Error codes · Bosch

Bosch classic (Gen 2 to 4) error codes

All 41 Bosch classic (Gen 2 to 4) codes we have documented: what each one means, what stops working and what you can do yourself before going to a dealer. Applies to Gen 2-4, pre-smart system) with Purion, Intuvia, Kiox, Nyon (BUI350.

3-digit fault code shown on the on-board computer (Purion/Intuvia/Kiox/Nyon); the drive may switch off automatically depending on the fault.

Get Bosch news & firmware updates in Telegram
CodeMeaningWhat to do
410One or more buttons on the on-board computer are blocked.Check for stuck buttons, for example from dirt getting in, and clean them.
414Connection problem with the operating unit (remote).Have the cable connections checked by a dealer.
418One or more buttons on the operating unit are blocked.Check for stuck buttons, for example from dirt getting in, and clean them.
419Configuration error.Restart the system. If it comes back, see a Bosch eBike dealer.
422Connection problem with the drive unit.Have the cable connections checked by a dealer.
423Connection problem with the eBike battery.Have the cable connections checked by a dealer.
424Communication problem between components.Have the cable connections checked by a dealer.
426Internal time-out error. While it's active you can't view or change the wheel circumference.Restart the system. If it comes back, see a Bosch eBike dealer.
430The on-board computer's internal battery is flat (not on BUI350).Charge the on-board computer in its holder or via the USB port.
431Software version error.Restart the system. If it comes back, see a Bosch eBike dealer.
440Internal fault in the drive unit.Restart the system. If it comes back, see a Bosch eBike dealer.
450Internal software error.Restart the system. If it comes back, see a Bosch eBike dealer.
460Fault at the USB port.Unplug the cable from the on-board computer's USB port. If it persists, see a dealer.
490Internal fault in the on-board computer.Have the on-board computer checked by a dealer.
500Internal fault in the drive unit.Restart the system. If it comes back, see a Bosch eBike dealer.
502Fault in the bike lights.Check the lights and their wiring, then restart. If it persists, see a dealer.
503Speed sensor fault.Restart the system. If it comes back, see a Bosch eBike dealer.
504Distorted speed signal detected; assist is reduced.Check the spoke magnet is in the right place and adjust it. Make sure nothing has been tampered with (tuning devices).
510Internal sensor fault.Restart the system. If it comes back, see a Bosch eBike dealer.
511Internal fault in the drive unit.Restart the system. If it comes back, see a Bosch eBike dealer.
530Battery fault.Switch off, take the battery out and put it back, then restart. If it persists, see a dealer.
531Configuration error.Restart the system. If it comes back, see a Bosch eBike dealer.
540Temperature error: the system is outside its permitted temperature range.Switch off and let the drive unit cool down or warm up, then restart. If it persists, see a dealer.
550An unauthorised load (consumer) has been detected.Remove the load, then restart. If it persists, see a dealer.
580Software version error.Restart the system. If it comes back, see a Bosch eBike dealer.
591Authentication error.Switch off, remove and reinsert the battery, then restart. If it persists, see a dealer.
592Incompatible component, usually the display.Use a compatible display. If it persists, see a dealer.
593Configuration error.Restart the system. If it comes back, see a Bosch eBike dealer.
595, 596Communication error.Check the wiring to the drive unit and restart. If it persists, see a dealer.
602, 603, 640Internal battery fault.Restart the system. If it comes back, see a Bosch eBike dealer.
605Battery temperature error: the battery is outside its permitted range.Switch off and let the battery cool down or warm up, then restart. If it persists, see a dealer.
606External battery fault.Check the wiring and restart. If it persists, see a dealer.
610Battery voltage error.Restart the system. If it comes back, see a Bosch eBike dealer.
620Charger fault.Replace the charger and contact a Bosch eBike dealer.
655Several battery faults at once.Switch off, remove and reinsert the battery, then restart. If it persists, see a dealer.
656Software version error.Ask a Bosch eBike dealer to update the software.
7xxFault in a third-party component (for example an electronic gear hub).See the manual of that component's manufacturer.
Blank displayInternal fault in the on-board computer.Switch the eBike system off and on again.
  • Most codes: restart the system first; if the code returns, see a Bosch dealer.
  • Connection codes (414/422/423/424) usually mean a plug or cable problem - have them checked rather than opening components.
  • Display blank = internal fault of on-board computer: switch system off and on.

Written in our own words from the manufacturer’s documentation. Codes can change with firmware; your dealer’s diagnostic software has the final word. Sources: terratrike.com

FAQ

What does Bosch 503 mean?

Speed sensor fault. What to do: Restart the system. If it comes back, see a Bosch eBike dealer.

What does Bosch 540 mean?

Temperature error: the system is outside its permitted temperature range. What to do: Switch off and let the drive unit cool down or warm up, then restart. If it persists, see a dealer.

How do I avoid Bosch error codes?

Most codes: restart the system first; if the code returns, see a Bosch dealer. Connection codes (414/422/423/424) usually mean a plug or cable problem - have them checked rather than opening components. Display blank = internal fault of on-board computer: switch system off and on.

Motors: Bosch Performance Line CX. Bosch firmware updates. Other systems: Bosch Smart System, Shimano STEPS / EP, DJI Avinox, TQ HPR, Fazua Ride 60, Specialized Turbo, Yamaha PW, Giant SyncDrive.